BoSL Board v0.3

BOSL BOARD - THE ULTRA LOW POWERED IOT LOGGING DEVICE

BoSL Board (rev 0.3)

This little beauty costs less than an Arduino and Sim5320a put together, yet it comes already assembled, runs on 4v, is ultra low power consuming (we removed all the overheads of the off the shelf arduinos) and can send data via the CAT-M1 or NB-IoT networks! We estimate that these things can log each minute for over 12months!

Specifications

Physical Specifications:
Board Width: 88 mm
Board Length: 68.5 mm
Board Height: 18 mm
Weight:

Electrical Specifications:
Max Input Voltage: 5.5 V
Typical Sleep Current: -- μA
Supply Current Surge Requirement: -- mA

Physical Layout

BoSL Board Front

BoSL Board Back, Note Pinout Labeling

Reference Table: BoSL Board Front

1	DC Power Jack
2	I2C IO
3	Power IO
4	Antenna Connector
5	Reset Button
6	SIM Card Holder
7	Digital IO
8	Analog IO
9	Analog IO\TTL Header
10	Integrated Pressure\Temperature Sensor
11	SD Card Holder
12	8P8P Modular Connector
13	Micro USB Port

BoSL BOARD V0.3 PIN LAYOUT

ATmega328P Pin Number	Arduino IDE pin	Internal Use	Application Notes
1	Reset	RST	Pull Low to reset Arduino
2	D0	USB RX	Free for use when no micro-USB connected
3	D1	USB TX	Free for use when no micro-USB connected
4	D2	SIM7000 RX	Not Available for use
5	D3	SIM7000 TX	Not Available for use
6	D4	SIM7000 On/Off	Not Available for use
7	VCC	VCC	N/A
8	GND	GND	N/A
9	Crystal	XTAL	Not Available for use
10	Crystal	XTAL	Not Available for use
11	D5	SIM7000 DTR	Not Available for use
12	D6	None	Free for use
13	D7	None	Free for use
14	D8	None	Free for use
15	D9	None	Free for use
16	D10	SD Chip Select	Free for use with no SD card inserted
17	D11	SD MOSI	Free for use with no SD card inserted
18	D12	SD MISO	Free for use with no SD card inserted
19	D13	SD Serial Clock	Free for use with no SD card inserted
20	VCC	VCC	N/A
21	Aref	None	Free for use
22	GND	GND	N/A
23	A0	None	Free for use
24	A1	None	Free for use
25	A2	None	Free for use
26	A3	None	Free for use
27	A4	SDA	Free for use when not operating I2C bus
28	A5	SCL	Free for use when not operating I2C bus

SIM7000 SIM CARD COMMUNITCATION ISSUE

2019/11/21:

There has been an issue where some of our boards aren't recognising the SIM cards, and so can't upload any data. To detect is if the issue is present the following AT command sequence can be sent.

GOOD RESPONSE

Command	Response
AT+CFUN=0
	+CPIN: NOT READY
	OK
AT+CFUN=1
	OK
	+CPIN = READY
	SIM READY

BAD RESPONSE

Command	Response
AT+CFUN=0
	+CPIN: NOT READY
	OK
AT+CFUN=1
	OK
	+CPIN: NOT INSERTED

We did some probing around with an oscilloscope to see if there were any electrical differences between the good and bad boards. Both had identical measured crystal frequencies of 7.9 - 8.1 MHz and SIM7000 - ATmega382p baud rates of about 9540.

The one difference which was found was in the signals issued from the SIM 7000 to the SIM card on pins SIM_VDD, SIM_RST, SIM_CLK, and SIM_DATA. They are quite different. Notably the bad boards only power the SIM VDD line for 3 pulses of 24 ms long whereas the working boards good boards keep this line high. The measurements are taken after the AT+CFUN=1 command is issued in the above test sequence.

In doing some reading on the issue it seems to have been encountered before, with the conclusion that it likely a soldering issue, possible inside the SIM7000 modual, thus leaving little course for it to be able to repaired.

for boards with a SIM inserted

PIN	Good Board	Bad Board
SIM_VDD	GOOD VDD SIM	BAD VDD SIM
SIM_RST	GOOD RST SIM	BAD RST SIM
SIM_CLK	GOOD CLK SIM	BAD CLK SIM
SIM_DATA	GOOD DATA SIM	No Reading

for boards without a SIM inserted

PIN	Good Board	Bad Board
SIM_VDD	GOOD VDD NSIM	BAD VDD NSIM
SIM_RST	GOOD RST NSIM	BAD RST NSIM
SIM_CLK	GOOD CLK NSIM	BAD CLK NSIM
SIM_DATA	GOOD DATA NSIM	No Reading